『壹』 「模具」英文是怎麼拼寫的啊求...強求
mould 澆築模具
die 沖壓模具
progressive die 拉伸模具
『貳』 在模具專業術語中，CAV、COR是哪些英文單詞的縮寫中文是什麼意思
在模具專業術語中，英文縮寫CAV的全稱是【Cavity】，漢語意思是【前模模仁】
在模具專業術語中，英文縮寫COR的全稱是【Core】，漢語意思是【後模模仁】
相關重要縮寫還有：
【CAI】【Cavity Insert】【前模鑲件】
【COI】【Core Insert】 【後模鑲件】
【CAP】【Cavity Pin】 【前模鑲針】
【COP】【Core Pin】 【後模鑲針】
『叄』 管子的"壁厚"用英語怎麼說
tube thickness
『肆』 模具中的中央頂塊英文怎麼寫
模具中的中央頂塊
Central top block in mold
模具中的中央頂塊
Central top block in mold
『伍』 鋼管的公稱外徑和鋼管的公稱壁厚用英文怎麼翻譯
我只知道
outer diameter
thickness
『陸』 我們的模具據說因為偏心導致產品壁厚偏薄，這個偏心怎麼翻譯呢知道的高人指導下~謝謝~
mismatch between cavity and core.
『柒』 模具類英文，請高手幫忙翻譯，非常感謝！
在我們努力確保我們收到鞋是從防霉免費當它到達我們的配送中心，我們修訂和加強預防措施的模具現在強制所有自助團體和/或特困鞋類供應商採用。如果一般工廠沒有進行清洗，或地方質量保證檢查不符合的潔凈標准感到滿意，細節將顯示在模具預防清單，工廠將被視為拒絕，不適合我們的生產，直至，倍的一般清潔工作已經完成正確
『捌』 美標、日標、德標鋼管外徑壁厚對照表上的英文部分代表什麼
這是鋼管的尺寸，壁厚對照表
Nonimal pipe size:公稱管尺寸
Outside diameter: 外徑
Nominal wall tickness:公稱壁厚
粉色部分就是他們分別表示多大或多厚
『玖』 求模具(沖壓鑄造塑料都行)或者材料類的外文翻譯，要5000字左右，最好中英都有，只有英文的也可以
Abstract: This paper analyzes thin tube slender tube-type plastic pieces of the structural characteristics of the process. And in accordance with the characteristics described in detail tube plastic parts injection mold structure and its working process, to determine a reasonable way of injection and mold release.
Key words: Process; gating system; ribbed tube; Injection Mold
1 Introction
In the mold design process, often encountered in long thin tube-type injection parts, such parts of the larger aspect ratio, and shape permit must have the taper. Injection molding of such parts, there are often non-uniform tube wall thickness, surface with flow defects such as marks and charred. Therefore in the design of injection molds need to consider the casting mold system, exhaust system, cooling system, the introction of the system. At the same time should also be considered loaded mold mold mold height and open itinerary. Mold structure as far as possible, compact, open-mode trip short.
2, process analysis
Shown in Figure 1 for the plastic tube size chart. Materials for the PS (polystyrene). We can see from the parts belong to the shape of thin elongated tube-type injection parts, die design and die in the process to determine the structure needed to be considered. Fig know by the size, wall thickness 1.5mm, the outer diameter size! 24mm, length 150mm, there is at the bottom of tube M24 × 30mm outer thread of the ordinary. Proct requirements of uniform wall thickness, internal and external cavity surface smooth, burr-free edge fly.
Because of long thin tube-type injection parts, such parts of the larger aspect ratio, it focuses on mold design and injection molding Demoulding selection on the way. Because of thin-walled tube, and筒身longer, it had not yet reached the molten plastic in the entire cavity is likely to occur before condensation and should not make a complete injection molding parts. In addition such slender parts by injection mold machine and therefore can not be away from the conventional way of Demoulding Demoulding.
Injection molding machine according to the selection of proction conditions in the SCZ-125-type injection machine. Their specific parameters are: a high degree of loading mode: 150 ~ 300mm. Open-mode distance: 300mm. The level of column spacing: 400mm. Vertical column spacing: 400mm. A maximum injection capacity: 125g.
3, mold design
Three die structure using one mold plate structure 4.
Plastic parts to determine the shrinkage rate of 1.3%. Demoulding gradient plastic parts in accordance with the molding process characteristics and the characteristics of plastic parts selection Demoulding cavity gradient 0.6 °, angle core Demoulding identified as 0.5 °, Figure 2 shows Demoulding add gradient plastic parts after various parts of the material thick-size map.
Because of plastic parts at the bottom there is the outer M24 × 30mm thread, it must die structure using fractal lateral agencies. Injection Mold through the spring and the role of lock block to complete block of lateral Hough fractal core-pulling action.
Injection Mold Design Demoulding manner shown in figure 3. Push the board to adopt the way the introction of plastic parts. And to rece the top of the distance from the injection molding machine using a direct role in the top bar at the push plate. Greatly reces the loading height mode.
翻譯：
摘要：分析了螺紋管細長筒薄類塑料件的工藝結構特點.並根據特點詳細論述了螺紋管塑料件注射模具結構及其工作過程，確定了合理的注射及脫模方式.
關鍵詞：成型工藝；澆注系統；螺紋管；注射模
1、引言
在模具設計過程中，經常會遇到細長筒薄類注射零件，這類製件的長徑比較大，且外形允許有一定的錐度。注射成型這類零件時，常常出現筒壁厚度不均勻，表面帶有流痕及燒焦等缺陷。因此在設計注射模具時需要綜合考慮模具的澆注系統、排氣系統、冷卻系統、推出系統。同時還要考慮模具的裝模高度及開模行程。盡量使模具結構緊湊，開模行程短。
2、工藝分析
圖1 所示為螺紋管塑件尺寸圖。材料為PS(聚苯乙烯) 。由零件形狀可知屬於細長筒薄類注射零件，在模具設計及模具結構的工藝確定中需加以考慮。由尺寸圖所知，壁厚1.5mm，其外徑尺寸為!24mm，長度為150mm，在筒底部有M24×30mm 的普通外螺紋。產品要求壁厚均勻一致，內外型腔表面光滑，無飛邊毛刺。
由於細長筒薄類注射零件，這類製件的長徑比較大，故模具設計的重點在於注射成型和脫模方式的選擇上。由於筒壁較薄，而筒身較長，故熔融塑料在還未達到整個型腔前就有可能出現冷凝而使得注射零件不能完整成型。另外這類細長零件受注射機的開模距離的限制而不能以常規的脫模方式進行脫模。
注射機的選擇根據生產條件要求安排在SCZ-125 型注射機。其特定參數為:裝模高度：150～300mm。開模距離：300mm。水平柱間距：400mm。垂直柱間距：400mm。一次最大注塑量：125g。
3、模具設計
模具結構採用三板式1 模4 件結構。
塑件的收縮率確定為1.3%。脫模斜度根據塑件的成型工藝特點及塑件的特性型腔選擇脫模斜度0.6°，型芯脫模斜度確定為0.5°，圖2 所示為加脫模斜度後塑件各部分的料厚尺寸圖。
由於塑件底部有M24×30mm 的外螺紋，故模具結構必需採用側向分形機構。注射模具通過彈簧和鎖塊作用來完成哈夫塊的側向分形抽芯動作。
注射模脫模方式的設計如圖3 所示。採用推板推出塑件的方式。而為減少頂出距離，採用注塑機頂出桿直接作用在推板上。大大減少了裝模高度。
『拾』 在模具專業術語中，英文縮寫CAV、COR是哪些英文單詞的縮寫中文意思又是是什麼
cavity有型腔(前模，母模)的意思，縮寫為CAV
core後模的意思縮寫為COR